Newsletter
How to use Toyota G and H Chip
Matched product:
Toyota G and H Chip Key Transponder OBD Remote Toyota Key Programming Tool
Latest price:US$21.00US$19.0010% off
- Item No. SK181
- Free Shipping
Toyota G and H Chip Vehicle OBD Remote Key Programmer can work For 4D67,68,72(G), supports both G and H chip vehicle via OBD2 port , tested on 2015 Camry. Free shipping to all over the world.
US in Stock, No Tax
US in Stock, No Tax
Part 1: How to use Toyota G and H Chip
Part 2:Customers Questions &Answers
Part 2:Customers Questions &Answers
Part 1: How to use Toyota G and H Chip
There is a new OBD device that No softwaqre, laptop or other accessories required. No need to take parts from vehicles. Can program Toyota G and H chip (4D/67/68/72(G)) car transponder directly via OBD diagnostic socket.
Easy 5 steps:
There is a new OBD device that No softwaqre, laptop or other accessories required. No need to take parts from vehicles. Can program Toyota G and H chip (4D/67/68/72(G)) car transponder directly via OBD diagnostic socket.
Easy 5 steps:
Step 1:
Get in the car and close the door. Insert the original key and turn switch ignition to “ON” position.
Step 2:
Switch to “ADD TRANSPONDER” and insert the key programmer device into OBD connector. You will hear two beep sound (Dee-Dee), it will start to add the remote.
Step 3:
After two beep sound, you will hear continuously beep sound, the device indicator light will flash during the procedure.
Step 4:
After the sound (Dee- Dee-),open the door, when hear the sound blaring. Press “Lock & unlock” key at the same time. And press the “lock” key. If the blaring ends, it’s OK.
Insert the new transponder, no need to turn it, the indicator light will turn into flash.
Step 5:
The indicator will turn off after 60 seconds, then it’s done.
Part 2:Customers Questions &Answers
I start by closing all doors, the red anti-theft light is flashing as shown in the attached picture. Then I insert the master G chip key and turn to ON position. The flashing anti-theft light has turned off. Then I connect the Toyota G and H OBD remote Key Programmer with the switch set to the LEFT into OBD port. I hear two dee sounds (dee-dee) and wait more than 3 minutes, but the red anti-theft light does not come on at all and there is no sound at all. I waited more than 5 minutes and still nothing.
What else should I be doing. Is it possible that the key programmer that you sent me to be defective?
Solution:
1. Ensure if your G chip is normal.
2. Operate as follows: get on the car, close the door, insert the key, turn the key, insert the key programmer via the OBD port. In the sound (deep layer), it will start adding remote controls.
When you hear two dee sounds (dee-dee), open the door. When the sound becomes harsh. Press the "Lock and Unlock" buttons at the same time. And press the "lock" button. If the high end, nothing.
Note: The switch is on the right (adding a remote control). If it is a high pitch, that's OK.
PS: The switch is on the right (add a remote controller)
Toyota adds a transponder:
Get on the car, close the door, insert the master key into the lock, turn the key, and insert the key programmer into the OBD port. If it sounds twice, it will start adding transponder.
You can hear the sound (dee -dee), after 2-3 minutes, the anti-theft light is on. Then remove the key (the anti-theft light will flash), insert a new key, no need to turn the key,
The anti-theft light will turn off.
Note: The switch is on the left (add the transponder)
If it doesn't work, it may be that the box has a problem.