This is a package offer include BMW ICOM A3+B+C+D Diagnostic Tool and V2019.03 ICOM HDD ISTA/D 4.15.12 ISTA/P 3.65 , the wifi have been preset, ready to use.
New BMW ICOM A3+B+C+D Diagnostic Tool Plus V2019.03 ICOM HDD ISTA-D 4.14.20/4.14.14 ISTA-P 188.8.131.520
ICOM A3+B+C+D Function:
1. A3- OBD diagnostic supporting MOST, D-CAN and K-CAN protocols
2. B - diagnostic via MOST bus, and have connection to A-interface via USB connection.
3. C - 20-pin cable for old models.
4. D- ICOM-D Motorcycles Motobikes Diagnostic Cable
BMW ICOM A3 Features:
1. BMW ICOM A3 Hardware Version: V1.40
2. Support Vehicles: BMW Cars, BMW Motorcycle, Rolls-Royce, Mini Cooper
3. Support BMW All Series Diagnose and Programming
4. Device main board contain WIFI chip, package come with WIFI adapter. Support wireless connection between ICOM A3 and laptop. But when you do programming, can not use WIFI, it is not as stable as cables.
BMW ICOM A3 Special Features Compared with BMW ICOM:
The modified BMW ICOM A3 for vehicles with OBD access receives a significantly more powerful processor and more storage capacity.Robust aluminium case will help to avoid damage when using in harsh environments.
YOU have to know before you buy ICOM A2 or ICOM A3 or ICOM Next:
BMW ICOM NEXT vs the old ICOM
-> much faster in BMW F and G series ..
-> supports gigabit Ethernet too to be future proof, there currently is not gigabit Ethernet protocol defined yet for autos. Also it has USB3.0 instead of USB2.0 and a better wifi card.
ICOM NEXT A vs ICOM A2
-> more stable during programming
-> be necessary for the future Gbit cars
-> faster start-up times and high throughput
-> through high-performance,low-power ARM SoC
-> improved handling
-> more flexible OBD cable
-> lighted button for logs
ICOM A vs ICOM A2 vs ICOM A3
Modified ICOM A2 for vehicles with OBD access receives a significantly more powerful processor and more storage capacity. And robust aluminium case
will help to avoid damage when using in harsh environments. It works better in cooling, runs faster and works more stable, not easier broken than older ICOM A.
ICOM A3 can program all units for all BMW series expect media system, and work more stable and has stronger compatibility than ICOM A2, A1.
Backwards compatible to car adapters (ICOM B, C) and motorcycle adapters (ICOM D, E)
03.2019 BMW Software Update
1. Updated ista-d to 4.15
2. Updated ista-p to 3.66
3. Updated ETK to Feberary ,2019
4. Updated KSD to Feberary ,2019
BMW ETK: 2018.07
BMW KSD: 07.2018Multilanguage
BMW FSC Navigation Code Generator
BMWAiCoder for BMW Coding
With free BMW Engineer Software (INPA, NCS, WinKFP, E-Sys 3.32.1, Psdzdata 5.06.01), BMW FSC code generator and BMW AiCoder
ISTA-P Multi-language available in diagnosing, programming and TIS diagram circuit: , British English, German, Spanish, French, Italian, polish, Portuguese, Turkish, Czech, Swedish, Dutch, Indian, Greek, Russian, Simplified Chinese, Traditional Chinese, Japanese, Korean and Thai.
ISTA-D new version support instructions:
Support for the new F, G and I series models, as well as Rolls Royce, MINI, BMW Motorcycle.
The new version provides Multi-VCI, which supports D-CAN line, ENET line, ICOM, OPS/GT1 direct connection diagnostics.
Can view maintenance materials, circuit diagrams, etc.
Dual-core processor, better above I3; over 4G of memory
It is recommended to use Lenovo ThinkPad: T61, T400, T410, T420, T430, X61, X200, X201, X220 X230 and other laptop with Intel chipset, such as I3 I5 / I7 series.
BMW ETK: 2019.03
BMW KSD: 03.2018 Multilanguage
BMW FSC Navigation Code Generator
BMWAiCoder for BMW Coding
With free BMW Engineer Software (INPA, NCS, WinKFP, E-Sys 4.09.13 e-sysplus 4.09.13, tool32 61.5, BMW FSC code generator, newly added Dr.gini B020 diagnostic software, BMW AiCoder.
Dr.gini B020 diagnostic software requires Ediabas properly installed and functional with a communication interface ( ICOM, ICOM Next, ENET, PASSTHRU or K+DCAN ),
the BMW manufactured before 2003 are not supported.
1pc x BMW ICOM A2 Interface
1pc x BMW ICOM B Most
1pc x BMW 20pin Cable
1pc x BMW ICOM D Cable
1pc x USB Cable
1pc x OBD2 Cable
1pc x LAN Cable
1pc x 2019.03 BMW ICOM HDD 500G
How to set wifi about the item bmw ic omwith wifi
1.Newest Version ICOM A2+B+C For BMW Diagnostic & Programming Tool
1.with latest Software, Adapter and WIFI .
2. It is Second generation of BMW ISTA Diagnose and programming system.
3. Best BMW ICOM.
2.How to set wifi about the item bmw icom with wifi
Pay attention the bmw icom wifi setting
1.Usb wifi insert the computer usb connection firstly.
2.Close the computer wifi itself and other new added wifi, only ours device usb wifi, Wired connection port can not connect cable or device.
3.after confirmation, then boot computer.
4..And then confirm all the network is turned off and no connection of wired cable
The picturer shows wifi can not turn off, it is ours wifi.it is normal when it shows”X”
5.Start softwae and choose wifi for ICOM.
6.And then connect icom a2 to car, wait 20 to 60 seconds, you can see the device wlan led not blinking or slowly blinking.
It shows usb wifi and icom a2 wifi communication is ok.
7.Now you can click diagnosis or programming software)
when you get this notice, just click ok.Ad don’t close it, just narrow it down.
recognize the device normally
3.How to enable BMW ICOM A2 to work with ISTA-P v3.59 ?
In order to enable the BMW ICOM A2 firmware to work well with ISTA P v3.59, you need a valid ICOM A2 license or ISTA-P loader firstly.
In other word, BMW ICOM A2 requires valid firmware license. If you have no license, you just update firmware to latest version and use ista-p loader v4.9 (v5.x discontinued).
Free download ISTA P Loader (for those with ista p but data is gone)
ISTA-P 184.108.40.2060 (tested OK, with Loader v4.9)
V2016.7 BMW ICOM Software HDD ISTA-D 3.55.31 ISTA-P 220.127.116.110 with Engineers Programming Windows 7 System
User feedback on ISTA/P and loader
More info on ISTA P loader:
Tried running Rheingold ISTA/P 18.104.22.168 using v3.2 loaded.
Select K+Dcan emulator, which started fine. (network tool for kdcan is necessary)
Select BMW car and ista/p loaded up.
Start new session. Fine.
Select my machine.
Select interface. all good so far.
On the next page I had a progress bar on the bottom left.
First job finished, then it said “Determining Vehicle Identification number”
Then things stopped and I got an error box come up saying:
“An error on execution of the measure.
94201 Technical service initialisation failed.
10007 (CIP)- Error during initialisation of EDIABAS.”
All help appreciated as this is getting frustrating.
Then run the network config tool for k+dcan:
Error solved. And ISTA/P works like a charm.
What to do if programming data is missing?
“Programming data” in launcher is for ISTA 4 only (I, F & G series). Requires separate install to ISTA/P.