New Genius & Flash Point OBDII/BOOT Protocols Hand-Held ECU Programmer Touch MAP Get Free FGTech Galletto 2-Master V50
- Shipping:
-
Express Shipping Service
Estimated delivery time: 5-7 workdays.See details ? - Weight:
- 1.6KG
- Package:
- 26cm*20cm*14cm ( Inch:10.24*7.87*5.51 )
- Returns:
- Return for refund within 30 days,buyer pays return shipping.Read details »

- Product Details
- Tech support
- Reviews
- Write a Comment
- Related Products
New Genius & Flash Point OBDII/BOOT Protocols ECU Tuning Tool Supprorted All Vehicle Catgeories
TOP 10 Reasons to get Genius ECU Tuning Tool:
2.Easy to use ,with touch screen and intuitive menu.
3.Get a free FGTech Galletto 2-Master as gift.
4.With ECM1.61 and Winols 2.24 inside the package
5. Completely independent of the PC during the phases of read/write.
6.Newest Hardware: 5.005, Newly Add More ECU Models, Like VAG DQ500 and VAG DQ250
7.World’s first Touch & Map device, allows you to read/programm the ECU in modern vehicles through OBD2
8. No tokens limitation:There is 30 tokens by default, after the tokens use up, you can simply press tokens reset button to reovery.
9.Kess V2 Update Version, Supports More Vehicles, directly connect cars and K TOUCH to read the data. Just install the software on PC to modify the data.
10.Multi-Language: English,Italian,German,French,Spanish,Portuguese,Hungarian

1.Never connect Network, operating system can be on WIN XP and WIN7.
2.No support Toyota obd only write med17.5.2. and 17.5.21 (not tested)
3.New Genius & Flash Point tokens reset button:
Firmware version: V5.05 (can read/write VAG DQ200&DQ250)
New Genius Master Compared to Best Kess V2 Master:
Product Name | New Genius | Best Quality Kess V2 (SE87-D) |
Language | English, Italian, German, French, Spanish, Portuguese, Hungarian |
English, German, Spanish, Italian, Portuguese, French |
Software | -- | V2.15 |
Hardware | V5.05 | V4.036 |
Tokens | No Tokens Limitation,30 Tokens come with device by default, you can press the tokens reset buttonon the back of hardware to get new Tokens | No Tokens Limitation, there is renew buttonon the main unit. This button is used to charge tokens. Once your tokens run over, just click this button, then tokens will go back to 30 tokens. |
Update | via hardware | via hardware |
Support Protocols | Supports CAN-BUS, KWP and J1850 protocols | Line, CAN, EDC17 and MED17 and Ford J1850 |
Support Vehicle | Car, Bikes, LCV Support more new vehicle than Kess V2 |
Car and Bike |
PC | Hand-held ECU Chip Tuning Tool, no PC need; software is inside the machine already directly to use | PC-based ECU Programmer, you need install the software by yourself |
Method | Read and Write ECU via OBD2 directly | same |
New Genius Master VS Kess V2 Master
Product Name | New Genius | Kess V2 (SE87-C) | Kess V2 (SE87-D) |
Language | English, Italian, German, French, Spanish, Portuguese, Hungarian |
English, German, Spanish, Italian, Portuguese, French | English, German, Spanish, Italian, Portuguese, French |
Software | — | V2.15 | V2.15 |
Hardware | V5.005.003 | V4.036 | V4.036 |
Tokens | No Tokens Limitation,30 Tokens come with device by default, you can press the tokens reset buttonon the back of hardware to get new Tokens | No Tokens Limitation,CD comes with token programmer, you can follow our video to program tokens. No need remove chips or desolder chips | No Tokens Limitation, there is renew buttonon the main unit. This button is used to charge tokens. Once your tokens run over, just click this button, then tokens will go back to 30 tokens. |
Update | via hardware | via hardware | via hardware |
Support Protocols | upports CAN-BUS, KWP and J1850 protocols | Line, CAN, EDC17 and MED17 and Ford J1850 | Line, CAN, EDC17 and MED17 and Ford J1850 |
Support Vehicle | Car, Bikes, LCV Support more new vehicle than Kess V2 New Genius ECU List |
Car and Bike | Car and Bike |
PC | Hand-held ECU Chip Tuning Tool, no PC need when you read and write ECU data; but you need install K-touch software to export and import ECU data | PC-based ECU Programmer, you need install the software by yourself | PC-based ECU Programmer, you need install the software by yourself |
Method | Read and Write ECU via OBD2 directly | same | sam |
Software Including:
The New Genius supports CAN-BUS, KWP and J1850 protocols and has communication modules available for the following vehicles:
Available in Master:
When you install PC software ,if it pops up below error,please try to download in the CD,you can also download from
: https://mega.nz/#!0YQkXI6C!ubU19RfbmKmSG3SzuAiAPldQHCGsvSA-U7unpYezbvs

Technical Specifications:
How do you know if new genius support your cars or not?

New Genius Customer Feedback:

Full newest collection of V5.005.003 GENIUS Ktouch ECU programmer review on what work and don’t work.
2016 Mitsubishi Montero Sport/L200 with 4N15 engine 2.4 DOHC MIVEC Turbo Diesel 181hp. Result :
Read -> OK
Write -> OK
2014 Chevrolet Spin 1.5 ECOTEC Petrol. Result :
Read -> OK
Write -> OK
2016 Chevrolet Trax 1.4 Turbo Petrol. Result :
Read -> OK
Write -> OK
2014 Chevrolet Spin 1.3 TDCi. Result :
Read -> OK
Write -> OK
2010 Mitsubishi Lancer GT 2.0 4B11 CVT. Result :
Read -> OK
Write -> OK
Tested psa edc17c10 read on boot and test write by obd ok
Can make Opel Zafira , Combo , Meriva Denso ECU
So, the device is working good…worth buy it, but you need to do checksum before insert in genius
Med 9.1.1 Audi q7 4.2 FSI ID & READ ok
Read edc17c19 Opel insignia, work very fast
Works ok, tested on Nissan navara read and write OBD, edc 15 Fiat read write obd, pcr 2.1 read. But doesn’t calculate checksum and don’t read full size file like kess and ktag. Is not kess with lcd is another interface but from same company.
Mine still working well. After 7x resetting the token counter.
Audi Q7. File read with New genius is 100% correct (size 0x27C000).
I have done BMW E46 318iecu without issues.
PSA edc17c10 read on boot and test write by obd ok
Successfully remapped a Range Rover sport 2.7Tdi, First attempt I just assumed software did checksum. Started car and cut out within 5seconds. Second attempt I did checksums in winols and wrote back to car and everything was fine. My kess v2 read a 2mb file and the dimsport read a 256kb file but all the maps were in the read!
Can bypass TPROT security and allow to to flash TPROT ecus without having to open the ecu to unlock it at the first place. You just flash your mod by OBD like you would on any other non TPROT ecu. (Although on TPROT ecus reading function is not available)
But the problem is, that you need to checksum the file with Race Evo on these ecus. Anything else will not work.
Installation OS:
Installed on XP in vm for now all ok.
Run it on Windows 10 x64 with SSD hard drive.
Focus MK2 2.0 Petrol
-> Read OK 2MB File, full read (no partial reading)
-> Write – Ori file OK
– Modded File with CKS -> NOT OK, Engine start with DTC Throttle Fail
– Modded File with CKS write with KESS V2 OK
– Conclusion => Read Only, write ECU Error or worst BRICKED
Tested on golf 7 gti 220HP simos18 NOT WORK !
Since the protocol enabled is an old version, it doesn’t cover all file sizes.
You will get “incorrect file size” error when you try to upload the file to the ecu.
Part 2: K-Touch what does not work:
Tested read & write fail on Toyota
K-Touch is a crap tool made from Kess 4.036 tech with a screen on it.
I would never use it on any kind of car, even not EDC15.
MED17. 5.2 – Jetta tsi 2.0 tp8/10
Fail to Write, fail recover many times with fans on
Recover with original file worked
It is possible to clone CiD, but need SD Card from China that has an EEPROM instead of PROM.
To be continued……
Packing list:

FAQ
1.Q:How to solve New Genius "Fatal error: Invalid version of Raceloc.dll" problem?

A: First, please try this way, click Install2 Software Download , then run the file, it will be ok.
Secondly, if you can't solve it this way, please change to our Windows XP system.
2.Q: Can i use new genius edite the ECU file and write it to new ECU?
A: For all our ECU programmer up to now, like New genuis, K-TAG, Kess v2 and fgtech. All can read the data from Old ECU and write it to new one. But cannot change or edite the ECU data you read out from the old ECU. If you want to change, you can choose ECM TITANIUM on our website, or something enable you change the ECU file. Then use our ECU programmer to write it to new ECU.
Another thing you need pay attention is, after you change the data, you need to use the tool which you use to change the data to do checksum.
3.Q:How to install new genius?
A: Note: Please disconnect network connection when installing and using K-touch!!!
Step 1: Install K-touch Setup
Open My Cmoputer
Open K-TOUCH software CD
Open K-TOUCH-E folder
Open Abode Reader 9
Accept license agreement
Read the K-touch user manual first
Open and install K-touch Setup
Click Next
Click Install
Select setup language
Click OK
Press Next
Setup wizard installation completed
Restart the computer
Your computer needs to be restarted before Race EVO Setup 1…
Click OK
Step 2: Register & Activate K-touch
Open CD software
Open K-TOUCH-E folder
Open K-touch Setup
Install setup wizard again followed the same procedure above
Click Next
Click Install
Select setup language
Click Next
This time to install Race EVO Setup 1
Click Next
Click Next
The next program will requires user to enter User Registration code (leave others blank)
Open the Adobe read me file again
Copy C7535 and paste it to Dimensione Sport Customer code column
Click Next
Click Next
Click Next
Race EVO setup is well installed
Remove the tick “Run Race EVO (rev.431 build 829) Setup 1 now”
Click Finish
Complete install K-touch setup
Click Finish
Step 3: Connect Genious ecu tuning tool with computer
Tips
- Connect Genious OBD2 ECU programmer with power adapter, then wait until the machine boot. If the machine cannot boot, please turn off power then connect to power again. Wait until machine boot.
- Connect the K-touch programmer with computer/laptop via USB cable, then start to read K-touch data
After well connected the machine
Install hardware wizard
Select “Install the software automatically (Recommended)”
Click Next
The wizard has finish installing the software for DimSport-New Genius Device
Click Finish
Open My Computer->Manager->Device Manager->Universal Serial Bus controllers-> DimSport-New Genius Device to make sure the ECU programmer is well connected with computer.
Step 4: Read & write K-touch data
Open K-touch software on desktop
Click “Accept definitely” to accept software license
If the system pops up “Please update database in Internet and enable technical features (this procedure must be completed within 3 days 333)” message, click NO to proceed
Click K-Touch tab->Explore
If the system prompts “GENIUS is not updated”, click OK
Explore to FILE folder
Open Read folder
Save 000 file to desktop
Extract header, click Yes
Back to Genius:\FILE, open Write folder
Click Import icon
Select Import file, click OK
Import the file “000” just saved on desktop
Read and write ktouch data completed. You can check the device information.
Back to Genius folder
Click Help tab->System information to check files with date, time and version
Click Help-> Information about…to check Genius K-touch device information

For any question, please contact us at:
Find us on your phone:



How to make purchase on Obd2eshop?
