Customer Questions & Answers
Question:
Q:Does Foxflash or KT200 Read and Write Mercedes Delphi CRD11?
Question:
Q:FoxFlash can’t read EDC17CP54. Besides, all cable connection is fine he had checked.
Question:
Q:I HAVE A QUESTION REGARDING THE MERCEDES SPRINTER W906 ECU DELPHI CRD3.PB0 AND W907 SPRINTER ECU DELPHI CRD3.PC0. THE TOOL SUPPORT FULL READ?
Question:
Q:How to Fix FoxFlash Software ‘Your computer is low on memory’ Error?
Question:
Q:SID309 OBD password unlock stop at 57%. Waited for 20 minutes and nothing was happening. How to make FoxFlash Software continue?
Answer:
A:Answer:
When reading password via OBD (IN CAR) please ensure immo system does not become active during reading..
Then the password will be stored, even with the error, check the content of the file with hexeditor to see if contains data
Reason:
Immo system. On this case try to find password on bench by the instruction, but this model is not supported.
Also, the file is not completely empty.
How to R/W SID309 after Unlock?
Select Driver:
-TOOLS BOOT MODE
-INFINEON TRICORE Boot
-SAK TC1767
Pinout 1
Pinout 2
When reading password via OBD (IN CAR) please ensure immo system does not become active during reading..
Then the password will be stored, even with the error, check the content of the file with hexeditor to see if contains data
Reason:
Immo system. On this case try to find password on bench by the instruction, but this model is not supported.
Also, the file is not completely empty.
How to R/W SID309 after Unlock?
Select Driver:
-TOOLS BOOT MODE
-INFINEON TRICORE Boot
-SAK TC1767
Pinout 1
Pinout 2
Question:
Q:How to Read ECU with FoxFlash via Hotspot Outdoors?
Answer:
A:Detail Steps:
Plug the cigarette lighter into the cigarette lighter plug on the car.
The other end of the cigarette lighter is connected to the Bench device to supply power to it.
Next Connect with the computer and turn on the computer, The software can’t be opened when the computer is not connected to Internet.
Take out the phone. Turn on personal hotspot. Then use the laptop to find the name of the WIFI hotspot turned on by the phone,enter the hotspot password.
If it shows that the connection is successful, you can open the FoxFlash software to read the ECU.
Plug the cigarette lighter into the cigarette lighter plug on the car.
The other end of the cigarette lighter is connected to the Bench device to supply power to it.
Next Connect with the computer and turn on the computer, The software can’t be opened when the computer is not connected to Internet.
Take out the phone. Turn on personal hotspot. Then use the laptop to find the name of the WIFI hotspot turned on by the phone,enter the hotspot password.
If it shows that the connection is successful, you can open the FoxFlash software to read the ECU.
A:1.Connect FoxFlash BENCH BOX with car via cigarette lighter cable to supply power.
2.Turn on personal hotspot on phone, use a laptop to search hotspot name and connect it.
Note: FoxFlash software cannot open when the computer is not connected to Internet. If it shows the connection is successful, you can open FoxFlash ECU Tool to start reading.
2.Turn on personal hotspot on phone, use a laptop to search hotspot name and connect it.
Note: FoxFlash software cannot open when the computer is not connected to Internet. If it shows the connection is successful, you can open FoxFlash ECU Tool to start reading.
By ErinWang
Seller
on Dec 7, 2022
0 of 0 found this helpful. Do you?
Question:
Q:Here is how to run FoxFlash software on other computers ?
Total 105 items, 20 items/p, current page 4/6.
Don't see the answer you're looking for?
Post your question