SEAT IBIZA 2012

1.6 TD SIMOS PCR 2.1
ID DETECTED——-OK
EEPROM FLASH LOCKED —–OK
READ LOCKED BY OBD ——–OK
WRITING MOD FIILE UNLOCKED FLASH ——-OK
ALL TIME 25-30 min
THANKS FOXFLASH

excelenct very great tool for me

Dacia Lodgy 2016

 Dacia Lodgy 2016
 bench metod
 rw/wr ok
 cks by Fox

Ford MD1CS005

Bench
Read OK
Write OK
Chk by Fox

Iveco Daily 2.3M-Jet 126ps
Iveco Daily 2.3M-Jet 126ps EDC16C39 ✅OBD Read ✅OBD Write ✅Chk

Godiag GT107+ DSG Plus can work with foxflash ECU programmer to read DQ200 and DQ250 TCU data. It needs to set GODIAG GT107 + analog ignition switch in “manual” mode.

---

Foxflash received,  read and write Mercedes Delphi CRD3PLUS A0 ecu OK ! 

---

Edc17 c46
Edc17 c46 all by obd, virtual read an write, cecksum by tool

Peugeot 208
EDC17C10
R/W bench
all OK
 

foxflash clone Mercedes Benz Siemens SIM4LKE transmission compressor success.

SIEMENS SIM 4L KE [C167] – Mercedes Benz [ Gasoline ]

Pinout

To read and write use the following driver:
→ TOOLS BOOT MODE
→ SIEMENS-INFINEON C167
→ Bosch – Flash 29F800

If the ECU doesn’t enter boot mode, proceed as follows:

→ Switch off the ECU and remove the grey wire.
→ Connect directly to ground the boot pin with a needle.
→ Switch on the ECU.
→ Remove the ground.
→ Launch the driver and click the read / write buttons.

*Some versions of ECUs have the flash locked in writing.

Note:

1. Fgtech galletto v54 clone can kill this ecu during reading – if there is vin in ecu galletto can wipe it out, and coding also.
2.Yanhua ACDP also has module 18 but can only renew SIM4LKE, need to adapt with DAS or Vediamo.

 

Foxflash arrived very fast , the product was as described, great communication with ERIN , I will test and report

FoxFlash Super ECU tool does the job like it its supposed to.

FoxFlash definitely equipped enough for shop environment. Does everything you could ask for and more. it's already paid for itself in the first hour of use Fiat Marelli MD9F JTAG mode, R/W, chk OK

---

Prompt service easy to use

Customer service was friendly, responsive, and knowledgeable. It saved me the cost of the unit first scan.

Smart 453

ecu me17.9.20 safe write and read 

-Edc17c41 BMW 520d f11 read write bench Manual checksum
-Edc17c50 BMW x3 -13 read write bench manual checksum
-Denso 76F00xx, Toyota auris read write obd checksum by fox
-Denso MB279700, Volvo v60 d4 vea, read unlock bench write obd checksum fox

Citroen jumper dcm7.1b – r/w , and the most asked (yes .. the checksum is made by te tool).

 

Foxflash Read Jaguar MEDC17.9 by OBD success. 

MEDC17.9 OBD is in the foxflash driver list.

But if the ECU has OTP protected, you need to do bench or use breakout to do it via OBD on bench.

For example:

OBD on the bench reading the MEDC17.9 with foxflash programmer+ godiag gt100 breakout box. I want to try and write the modified files via OBD after an OBD read. The ECU data that had been corrupted is now all OK.

I have had an interesting case with this ECU MEDC17.9 that had failed and had the OTP block. I read the Full flash via OBD, had the flash modified to delete CAT/AdBlue/DPF and EGR (use a tuning file service). When I got the modified file back, I decided to write it via Bench mode. I did the checksum correction using the original flash and flashed it via Bench mode 100% without any problems. The car is now starting and has no faults whatsoever and drives very well. We had brought it on a flatbed. Another great success with FoxFlash and a bit of experimenting.

 

---

FoxFlash Read and Write Alfa Marelli MM10JA Success. 

OBD mode:
The built-in OBD does not working. It does not read the ECU ID nor read/write ECU.

Boot mode:
It works fine in boot mode.

---

Foxflash Pinout to FCA CONTINENTAL GPEC4. 

BAM SPC5674 CONTINENTAL GPEC4 FCA Pinout

 

Connect with the multifunction cable the CNF1 on the pcb.

Read and Write ECU

Use the driver:
→ TOOLS BOOT MODE
→ MOTOROLA FREESCALE BAM
→ FCA CONTINENTAL GPEC4